bearing name:	ISO 21308KW33 bearing
Brand model :	21308KW33
outer diameter D :	Advisory mm
diameter d :	Advisory mm
thickness B :	Advisory mm
category:	RAD BEARING LTD
brand:	ISO 21308KW33
Remark:	21308KW33  bearing  price

---

Tolerances

Tolerance classes and the corresponding values for certain tolerance characteristics are specified in ISO 492 (for radial bearthese standards were aligned with general ISO GPS (Geometrical Product Specification) standards such as ISO 1101 and ISO 5459. ISO/TS 16281:2008 contains recommendations for the calculation of the modified reference rating life taking into considerationn and fatigue load limit of the bearing material, as well as tilting or misalignment, operating clearance of the bearing and Single bearings and matched bearing pairs arranged in tandem Normal Check availability of C2, C3, C4, C5, reduced ranges of stValues are valid for unmounted bearings under zero measuring load. Matched bearing pairs arranged back to back or face to face Reference number ISO 21308 22006E © ISO 2006 INTERNATIONAL STANDARD ISO 21308 2 First edition Road vehicles Product data exchange between chassi ISO/PRF TS 31657 3 Plain bearings — Hydrodynamic plain journal bearings under steady state conditions — Part 3: Functions for calculation of tilting pad journal bearings BRITISH STANDARD BS ISO 21308 22006 Road vehicles Product data exchange between chassis and bodywork manufacturers BEP Part 2 Dimensional bodywork exchange p

ISO 119 Plain bearings Tolerances Part 2:Tolerances

10 3000 :2019520 :ISO 119 Plain bearings Tolerances Part 2:Tolerances on form and position and surface roughness for shafts and thrus :PDFwww.doc885187845305511.html 16 2000 :2020618 BS ISO 120 Plain bearings. Pedestal plain bearings. Side flange bearing. :PDF :16 : 14:14:43 :4 2000 www.doc8829799049516442.ht ISO 281:2007 specifies methods of calculating the basic dynamic load rating of rolling bearings within the size ranges shown irdance with good manufacturing practice and basically of conventional design as regards the shape of rolling contact surfaces. This document was prepared by Technical Committee ISO/TC 123, Plain bearings, Subcommittee SC 7, Special types of plain bearings. This second edition cancels and replaces the first edition ( ISO 14287:2012 ), which has been technically revised. ISO 492:2014 specifies dimensional and geometrical characteristics, limit deviations from nominal values, and tolerance valuesace (except chamfers) of radial rolling bearings. The nominal boundary dimensions are defined in ISO 15, ISO 355 and ISO 8443. ISO 3290 1:2014 Rolling bearings —Balls— Part 1:Steel balls :PDF :20 : 10:25:13 :2 1000 www.doc880806187168

BS ISO 120 Plain bearings. Pedestal plain bearings.

2000 :2020617 BS ISO 120 Plain bearings. Pedestal plain bearings. Pillow blocks :PDF :22 : 15:22:24 :4 2000 www.doc8821661851779784.ht

Other bearings

---

24028K30W33 ISODescription: 14 1250 :20181023 :BS ISO 4379 2018 Plain bearings. Copper alloy bushes :PDF| :7| : 14:17:04| : www.doc889055072981638.html

22308KW33 ISODescription:bearing@qq 【iso9001、iso14001、iso/ts16949、crccas9100c 22308eg15kw3322308eg15kw33nn3026mbkrc

21307KW33 ISODescription:Single bearings and matched bearing pairs arranged in tandem Normal Check availability of C2, C3, C4, C5, reduced ranges of stValues are valid for unmounted bearings under zero measuring load. Matched bearing pairs arranged back to back or face to face

23218KW33 ISODescription: 625 :2019716 ©ISO01Plainbearings—Multilayermaterialsforthin walledplainbearingsPalierslisses—MatériauxmulticouchespourpalierslissesmincesINTERNATIONALSTANDARDIwww.doc884923977171021.html

21308KCW33 AH308 ISODescription: 1000 :20181226 bearingsPart1:Seismic protectionisolatorstestmethodsCISO76 1:005Elastomericseis GB/T 528 1998(eqv ISO 3www.doc889723834847021.html

240/800K30W33 ISODescription: · Standardization of all types and all sizes of bearing elements based on the principle of rolling motion, includingication and standardization of spherical plain bearings, i.e. plain bearings with spherical contact surface. ISO/TC 4/SC 4

22212KW33 ISODescription:Single bearings and matched bearing pairs arranged in tandem Normal Check availability of C2, C3, C4, C5, reduced ranges of stValues are valid for unmounted bearings under zero measuring load. Matched bearing pairs arranged back to back or face to face

23988KW33 ISODescription:ISO 281:2007 specifies methods of calculating the basic dynamic load rating of rolling bearings within the size ranges shown irdance with good manufacturing practice and basically of conventional design as regards the shape of rolling contact surfaces.

24076K30W33 ISODescription: · Standardization of all types and all sizes of bearing elements based on the principle of rolling motion, includingication and standardization of spherical plain bearings, i.e. plain bearings with spherical contact surface. ISO/TC 4/SC 4

24196K30W33 ISODescription:ISO 15312:2018 Rolling bearings Thermal speed rating Calculation ，，： ISO 15312:2018 ，。

240/530K30W33 ISODescription: · Standardization of all types and all sizes of bearing elements based on the principle of rolling motion, includingication and standardization of spherical plain bearings, i.e. plain bearings with spherical contact surface. ISO/TC 4/SC 4

23218KCW33 AH3218 ISODescription: 2500 :202017 ISO968:006/Amd.1:011E©ISO011–Allrightsreserved3Table9continueddDB1SS1CaC1bCbmax.max.min.max.mminmmmmmmmmmmmmmm808096—3 3/16170106440565www.doc883877369264611.html

23068KW33 ISODescription: · ISO Dimensional system and bearing numbers 1.2 Formulation of bearing numbers The rolling bearing is an important mstandardization of bearing numbers has been examined by ISO but not adopted. Now, manufacturers of various countries are using

24040K30W33 ISODescription:（International Organization for Standardization，ISO）。ISO“ISOS”，“EQUAL”——。ISO1947，ISO，ISO

22213 E K W33 AH313 NKEDescription:Product properties. Availability 0 pcs; Brand NKE; Item Number 22213EK W33 NKE; Technical details (EK W33) E=Features An Optim Symmetrical Rollers And A Pressed Steel Cage. K=Tapered Bore, Taper 1:12. W33=Lubrication Groove And Three Holes In Bearing

21314KW33 ISODescription:ISO/PRF TS 31657 3 Plain bearings — Hydrodynamic plain journal bearings under steady state conditions — Part 3: Functions for calculation of tilting pad journal bearings